Bosch · 800 · Benchmark · slide-in · induction · dual fuel · E011 E115
Bosch range repair in Olympia for the slide-in and induction kitchens
Bosch ranges came to Olympia with fifteen years of kitchen remodels, and most sit flush in a run of quartz on Cooper Point or in a West Bay condo.
- BOSCH Burner clicks nonstop
- ON PAPER one written figure after testing; say yes and the visit fee is already inside it
- SAME-DAY often open for a refrigerator losing cold · Open 8–7, Mon to Sat
Open 8–7, Mon to Sat · Sundays off · same-day visits often open, the shop confirms by phone · Woodland Square Loop, at the Olympia–Lacey line
Book a visit
Pick a day for the van
Three short steps: the machine, a day and an arrival window, then the address. The shop rings back to confirm, and the visit fee is quoted on that call.
- Pick the day and the window that suit you
- A call from the shop to confirm, no texts
- One written figure after testing, nothing started without your yes
- Visit fee folded into any repair you approve
E011 on a Bosch range means the touch control thinks a key is being held, often because of water on the glass, while burners that click nonstop usually trace to a wet or cracked igniter, a moisture-shorted switch or a failing spark module. If an induction zone ignores a pan, check that a magnet sticks to it. We ease slide-ins from tight cutouts unscratched; reserve a window online and dispatch will call.
Bosch ranges in remodeled Olympia kitchens
The Bosch range is a European machine built for the American slide-in slot, and it behaves like one. The gas cooktop uses a spark module that reigites any burner whose flame goes out, which is wonderful until a damp igniter makes every burner click at once. The induction models sense the pan through the glass and refuse to heat anything they do not recognize. The oven runs on a touch control that reports faults as E-codes with four digits on the newer models and three on the older.
We handle the full line, 300 series slide-ins through Benchmark dual fuel, in kitchens where the range has to leave a tight cutout without scratching anything. Bring us the code or the sound and we bring the part.
Bosch range faults we repair
Burners that click without stopping
One burner or all of them spark continuously, knobs off, usually following a boil-over or a wet cleaning. Bosch reignition fires whenever a flame is lost, so a wet or cracked igniter, a spark switch shorted by moisture, or a failing spark module keeps it going. We dry and test the igniters, check each burner switch, change a dead module, then seat the burner caps so the flame stays lit.
Induction zone that will not recognize the pan
The zone shows the pan symbol and never heats, or cuts out a minute in. Sometimes the pan is at fault, lacking a flat ferrous base of the right diameter. When a magnet sticks to the pan and the zone still refuses, the induction generator for that side of the cooktop or the sensor beneath the glass has failed. We test the generators and swap the dead one.
E011 and a control that thinks a key is stuck
E011 means the control has seen a touch held down for too long. Water on the glass after wiping, a warped panel, or a failing touch control all produce it. We clean and dry the panel first, since that clears many, then test the touch module and the connection to the power board, and replace the touch module when it is truly faulty rather than merely damp.
Convection fan silent or rattling
The oven bakes unevenly and the fan at the back is quiet, or it runs with a rattle that worsens as it heats. Bosch convection motors sit behind the rear wall and their bearings dry out; a blade bent by a dropped rack rattles too. We pull the back panel, replace motor or blade, and check the fan relay when the motor tests fine but never runs.
Oven slow to light or dropping out on dual fuel and gas models
The gas oven is slow to catch, or lights and then loses its flame mid-bake. The hot-surface igniter has weakened, or on propane houses toward Griffin and Summit Lake the conversion was done without the correct oven orifice and the flame lifts off the burner. We measure igniter current, check the orifice size against the fuel, and correct both.
E115 and E118 control and communication faults
E115 in most cases means the oven overheated or the control believes it did; E118 means the touch control and the power board have stopped talking. The first sends us to the temperature sensor and the heating relays, the second to the ribbon cable and connectors between the two boards, which corrode in a steamy kitchen. We test rather than replace, because these boards are not cheap.
Bosch oven codes we meet
| Code | What it usually means | What we do |
|---|---|---|
| E011 / E0110 | A touch key appears held down for too long, usually moisture on the panel or a failing touch module. | Dry and clean the panel, then test the module and replace it if the fault persists. |
| E115 / E1150 | In most cases an oven over-temperature condition, real or as read by a faulty sensor. | Meter the oven sensor and test the heating relays before deciding between sensor and board. |
| E118 / E1180 | The touch control and the power module have lost communication, often at a connector. | Inspect and reseat the ribbon cable and connectors, then test both boards. |
| E305 / E3050 | The oven door lock did not reach its expected position, usually during or after self-clean. | Test the lock motor and switches and release the door before replacing the lock assembly. |
How we work through a Bosch range
- Read the E-code and pull the stored fault list from the control
- Dry and test igniters, spark switches and module on gas cooktops
- Test induction generators and pan sensors zone by zone
- Meter the oven sensor, heating relays and convection motor
- Give you the part by name and a repair figure in writing before proceeding
Fee, scheduling and the details that matter
On a Bosch range the diagnostic visit is a paid call, and the office names the amount as you book. That covers a technician and meter at the range, the failed component identified in plain terms, and a repair figure written down before anything is ordered. Proceed and that written figure is understood to contain the visit fee; stop and the visit fee is the sum total. Nothing is added for the drive anywhere in our Olympia ring from the Woodland District shop, and if Bosch's own coverage still applies we point that out first.
Bosch ranges are booked inside the week, and igniters, spark modules and convection motors ride with us; an induction generator or touch module usually has to be ordered, and its installation visit is scheduled by us with no extra line on the invoice. The printed warranty term covers the part and our labor. Eld Inlet second-home owners can give their approval by phone or email and get the invoice emailed.
Bosch range questions
Why do all the burners on my Bosch cooktop spark at once?
Because the spark module fires every igniter together whenever any burner switch closes, and a shorted switch or a wet igniter looks like a closed switch. It usually follows a boil-over or an enthusiastic cleaning. Let it dry for a day with the breaker off; if it persists, one igniter or switch has failed and we replace it.
My Bosch induction range will not heat a pan that worked yesterday. Why?
First check the base of the pan with a magnet and make sure it is centered on the zone and flat. If the pan is right and the zone still shows the pan symbol, the induction generator or pan sensor for that zone has failed. We test the boards and replace only the one for the affected zones.
What does E011 mean on my Bosch oven?
In most cases it means a key on the touch panel has been detected as held down for longer than the control allows. Moisture on the glass is the usual cause, and a thorough dry with the power off often clears it. If it keeps returning with a dry panel, the touch control module is failing and we replace it.
Can you pull a slide-in Bosch out of a tight quartz cutout?
Yes, and we do it carefully. Slide-ins are leveled to the counter and often sit within a few millimeters of the stone on both sides. We protect the floor and the counter edges, lift rather than drag, and note the leveling so the range goes back exactly where it was. If the anti-tip bracket was never installed, we say so.
Is my Bosch range set up for propane?
If you are at Summit Lake, out Delphi Road, on Steamboat Island or around much of Black Lake, it should be, and sometimes it is not. A range still on natural gas orifices burns propane with a tall yellow flame and soots the pots. We check the orifice stamps and the flame, and correct a conversion that was done incompletely.
Full code sheet
All Bosch machines → · Bosch dishwasher repair → · Oven, Range & Cooktop Repair in Olympia →
How a visit runs
Four stages, none skipped
The price goes on paper before a screw comes out.
- 01
Tell us what it is doing
Ring or use the form; a phone photo of the display or the model sticker saves a step. The shop calls you back to set an arrival window, and once more as the van pulls off Woodland Square Loop.
- 02
Readings first, opinions second
The technician tests the suspect part with instruments, tells you in plain words what gave out, and writes the repair down as a single price. The visit fee is already inside that number.
- 03
Most parts ride in the van
Fill valves, defrost heaters, igniters, drum rollers, drain pumps, relays — the things well water, salt air and winter outages wear out on this shore of the inlet. If the part has to come in by order, the return trip is on us.
- 04
A test run, then the invoice
You see a full cycle run start to finish, the kick panels and floor go back the way we found them, and the warranty term is typed onto the invoice.
Bosch range in Olympia: one call, one figure.
Tell us over the phone or book a day online. A technician tests the machine and writes the repair down as one price with the visit fee folded in; your invoice spells out the warranty term.